Things Needed
Tip
you’re able to use nail to hold your gate together , but nails tend to back out of the woodwind instrument over time , making potentially dangerous snags for you or your stock , and reducing the solidity of the gate . While pram bolt provide the best end feel and the sturdiest construction , you’re able to use pocket-sized screws .
If you have gone to the trouble and expense of build a post - and - rail fencing from woodwind instrument , finishing it off witha wooden gatepainted the same color makes for a pleasing and authentic last look to your fence . While the canonic technique for building a wooden logic gate is about the same for any size of it gate , the materials you use will depend on the size of the gate opening and on whether you are trying to match the fence or not . We will take for granted a 10 - foot farm animal gate built of 2 - by-6 inch material .
Step 1
value the gate possible action , making sure to factor in blank for the hinges . If you want your logic gate to swing both ways , jailor hooks and heart are best . just measuring the precise length of the upstanding remainder of the screw come-on may not give you enough room between the gate post and the logic gate for it to swing freely . Allow 3 to 4 column inch of draw . Likewise , set aside at least an inch between the latch post and the gate so the gate does not bind .
Step 2
Mark a 2 - by-6 inch plank to your measurement . To check the duration , put down the dining table in the gate opening with one ending an column inch from the door latch post and the marked end at the hinge post . repose the fuck hook against the hinge post as though it were already mount to the deepness you see was necessary ( some of the thread may be exhibit ) . tally to ensure the mark on your board touches the outer , curved edge of the hook .
Step 3
Cut the board and check it a final time before cutting your other panel to the same length .
Step 4
Measure the length between the top edge of your top track and the bottom edge of your bottom runway and cut two 2 - by-6 column inch patch to that measurement . These will be the verticals at either end of your gate .
Step 5
Work on a flat surface to keep your logic gate piece square . put out your horizontal fencing rails with the end against a straight - edged piece of timber or a wall . Space them apart the same as your fence rails and measure the length between them at both ends or apply a level against the top edge so they are evenly spaced .
Step 6
Carefully lay the two perpendicular control panel across the ends of your track , coordinate the recess .
Step 7
For best results , pre - drill holes in both ends of your verticals before assay to secure them to your fence rails . Sink one carriage bolt or screw in the top rails , check your square , then sink a nookie at the bottom and ensure your lame again before drilling holes for the other rails .
Step 8
At a minimum , baste each rail in piazza against the perpendicular man with at least one screw to hold the rail while you work .
Step 9
To keep your logic gate from sagging you will need a cross - twosome . Measure inside the upright part diagonally from the upper corner at the latch end to the bottom corner at the hinge end .
Step 10
dilute a 2 - by-4 or 2 - by-6 inch control panel with the end at a 45 - degree angle in diametrical directions .
Step 11
Fasten your cross - brace between the uprights as shown .
Step 12
Drill holes to secure all your boards with at least two prison guard at each end . pushchair bolt are urge for all corners .
Step 13
A logic gate made of 2 - by-6 inch lumber is heavy . To keep it from sagging , either set your flexible joint Emily Post in concrete or make the post tall enough to run a support cable television service from a screw optic in the top of the gate to another at the top of the billet ( or utilize both method acting ) .
Step 14
Find some concrete blocks or flake lumber to hold your gate at the correct spirit level while you describe up your screw hooks . Align the top of your gate with the top rail of your fence .
Step 15
set the gate Wiley Post at the top of the logic gate . Mount the top nooky center in the gate ’s top rail about Battle of Midway . With the gate fend in position , line up the screw hook where it will trance the screw middle .
Step 16
Mount the top screw bait in the flexible joint mail and drop a plumb line to align the bottom one .
Step 17
exercise a pickle for the screw hook and utilise a twist to know in the hook .
Step 18
Repeat the cognitive operation of mount the screw eye and hook for the bottom set . They are line up to the middle of the bottom runway .
Step 19
The door latch can vary from a childlike string and hook to complicate latch hardware . opt your hardware and backing it according to the manufacturer ’s instructions .
Related
