Home»Ornamentals»Yucca
Yucca filamentosa ( YUK - uh fil - uh - men - TOH - suh ) is a florescence , evergreen plant shrub from the family Asparagaceae .
Native to the Southeastern United States , Florida and is popular thanks to its unique shape and brand - like leaf .
Blooming Adams Yucca Needle Plant – lenorlux | DepositPhotos
The industrial plant is easy to grow with canonical care needs . It develop indoors and outside , depending on how big you require the plant to grow .
Filamentosa run by several coarse name :
There are a issue oftypes of yucca plantsin the genus including :
Caring For Filamentosa Yucca
Size & Growth
Adams Yucca are tough plants with a slow emergence rate , but it is not a small plant . It can develop to 10 ’ feet tall when fully mature with leaf that spawn about 2.5 ’ groundwork long . The works spread about 2 ’ to 3 ’ wide .
The mass of this flora ’s height comes from the flower shuck maturate from the eye of the plant , open it a much taller visual aspect .
This is also where theyucca flowerswill bloom during the summertime season .
Attractive Adam’s Needle Yucca flower cluster up close – anmbph | DepositPhotos
Despite its native home in Southeastern U.S.A , Adam ’s Needle get in USDA hardiness zona 5 to 10 .
Flowering and Fragrance
Filamentosa Yuccahas a unique visual aspect . The foliage is characterized by bluish - green leave that arise to be 2 ’ to 3 ’ magniloquent . The leafage have a fine filament of kink yarn along the leaf edge .
The fundament of the plant has a stem canker of sharp , sword - shaped leaves that are 30 ” long and can spread to 4 ” wide appear in belated spring .
A specimen plant can take a farseeing time to bloom during its first effort , sometimes proceed up to three years without a bloom .
However , when it does , the flower spikes usually appear during the summertime month through the fall .
The creamy white flowers are in the shape of drooping white bell or incandescent lamp with a soapy fragrance .
Light & Temperature
Needle Yucca tolerates full Dominicus but also does well in areas fond tint .
If planting yucca plant indoor , a west facing window is best as too much sunlight exposure such as in a south cladding might dry it out .
It presage best in temperatures ranging from 65 ° – 75 ° degrees Fahrenheit .
This industrial plant is resistant to cold temperatures and frost and can make it in temperatures as low as 5 ° degrees Fahrenheit .
Watering and Feeding
The Needle industrial plant is drouth tolerant , but it still requires some level of moisture . urine the plant life more often during the grow time of year but reduce the relative frequency as winter approaches .
During the leap , and summertime season water system up to twice a calendar week . check that the beginning are n’t drown and bit by bit reduce to once a month in the colder months .
prey once every two weeks during the summer months with a good timber weewee - soluble fertiliser . The plant needs no alimentation during the declension or winter .
Soil & Transplanting
Adam ’s Needle plants need a well - drain land that ideally has a pH from 5.5 to 7.5 . However , it can brandish in poor , arenaceous soils .
Transplant Adam ’s Needle every three or four years into a larger pot in the wintertime calendar month . The pot should contain a concoction of backbone , garden soil , and top soil .
Grooming and Maintenance
If the atmospheric condition veers on the drying agent side , spray the plant life with piss to keep it looking fresh . Keep your plant life looking its best by tearing off yellowing leave after they have dry .
igniter pruning and withdraw branching from the trunks during the month from February to May .
However , be careful not to remove all the leaves . Leave a minimum of three leaves on each offshoot , or else it will become difficult for the leaves to grow back .
When deal Adams Filamentosa , take care to wear gloves for protection from the sharp-worded leaves that can leave rich slice .
Propagating Needle Yucca
Propagate Adam ’s Needle by seed ( pollenation is by the Yucca moth ) or stem cuttings . Remove one or several stems between 5 ” to 10 ” in long .
Allow the cut to dry out over before you implant filamentosa yucca in its raw home , which should be with a fibrous sandlike filth .
The stems should be proceed moist and place in a shaded location until roots begin to develop . This can take one to two months .
Needle Palm Pest or Disease Problems
Too much moisture can cause rust fungus in this Yucca works . This usually occur during wintertime . Prevent this by protecting the plants from heavy wintertime moisture .
Yucca Filamentosa also want insecticide regularly to keep slugs and snails at bay as these can damage the plant .
Adam ’s Needle is also prone to soupcon . This is characterized by speckle on the parting or the appearance of gray-headed WWW .
This can be prevented with miticides , pruning , and soaping with extra insecticidal grievous bodily harm .
Fungal diseases can come in the mannequin of spotted leaves with cherry - orange marks . These should be removed as soon as possible to prevent the disease from spread to other leave .
Using The Adam’s Needle
This plant is excellent as an indoor houseplant or as part ofyuccas in the out-of-door gardenor rock garden .
It grows in areas with otherwise poor soil or too much sun and can facilitate control soil erosion . The interesting appearing urinate it a gross addition to add some contrast to your plants .
